Method for using the Dr Hulda Clark Digital Zapper
(1)
Unpack Zapper, insert 9v Battery into compartment
|

Turn Plastic
Screws Left |

Clip 9V Battery
in place |
(2) Connect the Copper Hand Holds to the Black and Red connecters on Zapper 3
(3) Connect 110v wall adapter to the Zapper (front left)
(4) Press the Green On button (Numbers will appear on screen)
(5) Open the C.A.F.L frequency book
(6) Select an illness to be cured (e.g. Asthma .62)
(7) Dial the wheel until 100hz is reached (DISPLAY
SWITCHES FROM HZ KHZ AUTOMATICALLY)
(8) Press HOLD (the button above the yellow
button)
(9) Place the copper hand holds in palms or under soles of feet (put in your socks)
(10) For serious illness follow the Dr Robert beck Zapping method (zap up to 3 hours)
(11) Read the Books. Especially the C.A.F.L.
Book as it applies to the Zapper Digital 3 model.

General Specifications
Auto:
LCD indicator represents Automatically switching from Hz to Khz
RS232:
LCD indicator represents COMPUTER LINK ON. This is always set to on
[H]:
LCD indicator represents FREQUENCY LOCKED
022.4Khz:
LCD Frequency Display Sample
Khz:
LCD Indicator for Kilohertz (Khz). This
automatically switches to HZ using JOG DIAL
Frequencies
0 512 hz displayed in Hz Frequencies
.52Khz 50Khz displayed in Khz
HOLD:
Hold / Lock frequency button. For
locking in a Zapper Frequency
ON/OFF:
LCD indicator represents Automatically switching from Hz to Khz
RS232:
COMPUTER LINK button always on
Jog Wheel:
Adjust Zapper frequencies using the jog dial (According to Frequency Book)
10A:
Power adapter in 9VDC @ 1 amp. When
Power adapter is attached, Battery is AUTO off
mA:
Zapper Light On
COM:
Negative lead out (Black) to Copper Tube or wrist-strap
Hz:
Positive lead out (Red) to Copper Tube or wrist-strap
(2 x HZ outputs available)
Buttons:
The Only functioning buttons are:
(1) GREEN ON BUTTON
(2) BLACK HOLD BUTTON
(3) JOG WHEEL (FREQUENCY WHEEL)
(4) YELLOW BUTTON DISABLED (ALWAYS ON FOR AUTO COMPUTER RS232 LINKUP)
All other buttons are unused. The symbols on the Zapper 3 Jog Dial are electronic and are
not used.
See specifications (above) for more details.
Cables
The two cables provided are
(1)
Blue
Wrist-strap cable
(2)
Black
and Red Copper Hand Holds cable

Plug Cables into the
RED and Black Connecters on the Zapper 3
Using the blue wrist-strap cable on the arms may cause some sensitivity, if you feel any
itching or zapping sensations, then use the black/red cable in your palms or on the soles
of your feet (put in socks). Why? Zapping on
sensitive skin can cause rashes. To be safe
use only palms of hands or soles of feet.
MERIDIAN ZAPPING WITH 2 POSITIVE OUTPUTS
Follows the
Chinese Medicine meridians
Place the Positive (Red) lead into the V-Hz (RED) socket
Place the Negative (Black) lead in the COM (Black) socket
Place one of the Blue Wrist-straps in the Hz (RED) socket
Place one
Blue Wrist-strap around one ankle
Hold the Red and Black Copper Rods in the left and right
hands
This allows a zapping session where the positive output
frequencies travel from left side to right side and down the
leg.
You can also put the blue wrist-strap on the Black COM
socket, and attach this to your foot.
Plug the Black and Red Copper wires in the 2 RED sockets and
hold in both hands.
This will permit a left/right positive zapping experience,
and the foot-strap is ground
You could
also put 2 positive wrist-straps on the feet and hold the
negative copper bar in your hand.
If you experience any “stinging” sensation from the blue
wrist-strap on the ankles, then wrap the wrist-strap around
the foot, with the metal touching the soles of the feet.
Hertz or Kilohertz (Hz or Khz)?
Set
the centre Frequency DIAL on Zapper 3 (spin left) to ZERO. Find the particular Illness you wish to work with. Select first setting on the list and program this
into your Zapper 3 by turning the first dial. You
will see that the low frequencies 60
512 are in HZ, after 512hz the Zapper 3 automatically switches to KHZ. So the next number after 512hz is .52 Khz. Press HOLD
to lock in a frequency.
Remember to look at the HZ or
Khz LCD display on the screen HZ is low frequency (e.g. < 512hz) and
the Khz is high frequency (e.g. .> .53Khz)
IMPORTANT:
The CAFL book shows frequencies in HZ (eg 320hz) but does not indicate Khz (eg .82)
IF THE READING IN THE BOOK DOES NOT INDICATE HZ (eg 320hz) THEN IT IS AUTOMATICALLY A
KILOHERTZ FREQUENCY (eg .82). Hz AUTO switches to Khz when display is greater than 512hz
Zapper
3 covers over 60,000 possible frequencies, so the sensitivity is very high. If it is difficult to HOLD a particular
setting, then move dial until you are under (less than)
the desired frequency. Zapper
3 will automatically move frequency up a few points every few seconds; so if you wait a few moments you can click HOLD
on the desired frequency. Close enough is
good enough, a few points out will not be a problem.
Zapper
3 is both Battery and Mains Power. The Battery
is 9V at 100mAMP and the Power Pack is 9V at 1000mAMP.
The choice is yours which power source you use. Using the power pack at 1000mAMP you will
appreciate that Zapper 3 supplies a more powerful and greater penetrating Zapping session
If
Screen blanks out you may have to change battery.
A Battery sign flashes on the screen when battery is low. Battery
is 9V. Zapper will work always on power supply
provided. If you intend not to use battery you
may remove it from the Zapper and just use power supply provided.
Zapper 3
Digital Computer Communications
To use the Zapper 3 Digital with a computer,
you must have the following requirements:
(1)
An Windows XP / Vista Notebook
or Desktop
(2)
An available built in 9 pin
Serial Port or USB-SERIAL converter adapter.
(3)
A CD Drive to load program.
Load the CD provided into your computer
Open the folder “Zapper Digital Computer Link”
CLICK
<SETUP> AND INSTALL THE
PROGRAM

(1) PLUG SERIAL CABLE INTO THE COMPUTER AND THE ZAPPER CABLE
END INTO THE ZAPPER 3 DIGITAL AND PRESS START ON YOUR
COMPUTER SCREEN
(2) YOU MAY HAVE TO SET THE “COMM” PORT UNDER “SET”
(3) WHEN THE COMPUTER PROGRAM DETECTS THE ZAPPER DIGITAL,
THE PROGRAM WILL DISPLAY THE ZAPPER’S OUTPUT ON THE SCREEN,
THE COLUMN ON THE RIGHT WILL KEEP A RECORD OF THE ZAPPING
SESSION.
(4) SAVE SESSIONS WITH TIMES, DURATIONS, AND FREQUENCIES,
FOR RECORD KEEPING AND CLIENT DATABASES.
